Halloween is less than a week away. Can you believe it?
Today's project got its start when I first saw these gorgeous Halloween printable labels created by my friend Karen, aka The Graphics Fairy. I'll wait while you click over to see the labels. . .
Gorgeous, right? I love the ivory and black combination. A little bit gothic, a little bit dark Victorian, a little bit elegant too. I knew I wanted to make a set of apothecary jars, which I've seen examples of all over Pinterest. All I needed to do was carve out a small bit of time to make them. Sometimes that's easier said than done, right?
And speaking of mason jar crafts, you should check out my friend Johnnie's fantastic list of 50+ Mason Jar Decor Ideas on her blog Saved By Love Creations. You will definitely be inspired by all the mason jar eye candy there, plus each image links to more info on just how to create each project.
|Supplies . . .|
The supplies needed for this project are pretty simple:
Clear Glass Recycled Jars
Black Acrylic Paint
Foam Makeup Sponge
Halloween Printable Labels, printed and cut to size you need
Vintage style trims for embellishments
Start with clean jars. I didn't do anything special to clean these, other than running them through the dishwasher.
Sponge on black paint.
Using a makeup sponge - those foamy triangle-shaped sponges you can buy in large quantities at the drugstore - I sponged black acrylic paint all over the jars in a random pattern, making sure to cover the entire jar. I wanted each jar to look like it was covered in black soot, so I varied how heavy and light I applied the paint. I gave each jar three light coats in this manner, letting them dry for about 20 minutes in between each coat. After the third coat, let the jars thoroughly dry. (I let mine dry overnight.)
Spray each jar with a coat of acrylic sealer. Let dry.
Mod Podge labels to jars.
Apply a coat of Mod Podge to the back of each label, as well as to the part of the jar where each label will go. Place the label carefully onto the jar, smoothing out from the center. Wipe any bits of glue that seep out from the edges. (I just used my fingers in this instance, because the look of the jars is a bit messy to begin with.)
Use a brayer to smooth out.
I use a brayer when I Mod Podge to make sure every part of the paper is smoothed down and adhered all the way. Again, you'll get bits of glue that might seep out, just wipe those away with your fingers. (Or you can use a damp paper towel to wipe the glue away too.)
Roll the jar around.
Huh? Yes, that's what I said. Take your jar and roll it back and forth over some scrap paper or cardstock, as shown in the image below. Even after using my brayer, I will do this extra step when Mod Podging onto jars because it gets any remaining Mod Podge out, plus the slight pressure applied when rolling the jars gets those labels super smooth.
Repeat the above steps for each jar.
As these jars will be placed on a half-wall in our home, I want them to be decorated on the front and the back. So I chose 3 more labels to adhere to the back of each jar, as seen below. Repeat the same steps above to adhere each of these labels to the jars. Once dry, I applied some Mod Podge to the front of each label all the way just past each edge so that the glue goes ever so slightly onto the glass surface. Wipe away any excess. You want to make sure each label will be completely glued down.
Embellish the jars! Now comes the fun part . . .
|I scored this awesome trim at a neighbor's garage sale recently!|
First, I measured out the trim needed to go around the top of each jar. I applied a line of strong tacky glue around the upper rim of each jar, and pressed the trim into place.
Next I added some jute twine just below the trim, where my finger is pointing in the image below. Again, I measured out a long length of twine for each of the jars. All that was needed was a tiny bit of strong tacky glue to hold the "start" of the length of twine, and then another small amount to adhere the other end of the twine once I was done wrapping it around the jar several times. (Long sentence!)
Here's what the jute twine looks like close up. (As it was drying, I stuck those little hanging bits of the trim inside each jar, otherwise with my luck those darn things would have somehow become attached to the glue that was drying in the various crevices of the trim. Know what I mean?)
I added battery-operated flickering tealights, which I found in the Christmas section at the local dollar store. (And right there is a good reason to be happy that stores put out their Christmas merchandise so early. The fake tealights came in a set of four, with the packaging specifically mentioning Christmas. Score!)
Since the mood lighting wasn't doing it for me, I took everything outside.
|The front of the jars...|
I couldn't resist adding two black glitter spiders to the jars. You can see one of them on the center jar above. And you can see the other glitter spider on the left jar below. (The Graphics Fairy had an image of a spider hanging down just below the word "spider" so I thought it was the perfect spot to put the glittered version!)
|...and the back of the jars|
Here's a close-up shot so you can see the paint effect I created just by randomly sponging on the paint. I really love the way it looks - like the black soot I was imagining.
|Extreme close-up, so you can see the paint effect.|
Here's another angle so you can see more of the black soot "look" to the jars.
|...and the back|
I love the way these jars turned out! And now I'm (finally) ready for Halloween!
How about you?
I'm linking up to these great blog parties, below!
Click on each button and check them out for tons of crafty and DIY inspiration!